Φίλτρα

Κατασκευαστής (1)
074.0420
8,06 (9,99 με ΦΠΑ)
DFRobot, FIT0801
INTRODUCTION This super-easy-to-use air pump is very suitable for beginners to make inflatable or pneumatic projects. It is basically a  DC motor ,...
Μη Διαθέσιμο Προσθήκη στα αγαπημένα

074.0027
8,64 (10,71 με ΦΠΑ)
DFRobot, SEN0193, 5212019508803

This product measures soil moisture levels by capacitive sensing, rather than resistive sensing like other types of moisture sensor. It is made of a corrosion resistant material giving it a long service life. Insert it into soil and impress your friends with the real-time soil moisture data!


The product includes an on-board voltage regulator which gives it an operating voltage range of 3.3 ~ 5.5V. It is compatible with low-voltage MCUs (both 3.3V and 5V logic). To make it compatible with a Raspberry Pi, an ADC converter is required.

This sensor is compatible with our 3-pin "Gravity" interface, which means it can be directly connected to the Gravity I/O Expansion Shield.

The following image shows an example project - a device that notifies you when a plant needs to be watered.

Άμεση
+
Προσθήκη στα αγαπημένα

074.0014
9,00 (11,16 με ΦΠΑ)
DFRobot, SEN0205, 5212019508872

This is a photoelectric water liquid level sensor that is operates using optical principles. The advantages of this are good sensitivity and no need for mechanical parts - meaning less calibration! The corrosion resistant probe is easily mounted and can handle high temperature and high pressure. The sensor is equipped with an interface adapter for compatibility with the DFRobot "Gravity" interface.

Άμεση
+
Προσθήκη στα αγαπημένα

074.0025
10,40 (12,90 με ΦΠΑ)
DFRobot, SEN0189, 5212019508964

The turbidity sensor detects water quality by measuring level of turbidity. It is able to detect suspended particles in water by measuring the light transmittance and scattering rate which changes with the amount of total suspended solids (TSS) in water. As the TTS increases, the liquid turbidity level increases.


This sensor have both analog and digital signal output modes. You can select the mode according to the MCU as threshold is adjustable in digital signal mode.

Turbidity sensors can be used in measurement of water quality in rivers and streams, wastewater and effluent measurements, sediment transport research and laboratory measurements.

Άμεση
+
Προσθήκη στα αγαπημένα

074.0067
10,80 (13,39 με ΦΠΑ)
DFRobot, FIT0200, 5212019508995

This immersible pump can be used to water your plants, make a fountain or waterfall, even change your fish tank wter.It works quietly with the sound level under 30db.

Note: This pump is intended for use UNDER the water ONLY!

Άμεση
+
Προσθήκη στα αγαπημένα

074.0007
11,20 (13,89 με ΦΠΑ)
DFRobot, SEN0217, 5212019509015

The Gravity Water Flow sensor measures the rate of a liquid flowing through it.

The Gravity interface make it be compatible with Arduino IO Expansion Shield.

Άμεση
+
Προσθήκη στα αγαπημένα

074.0392
11,52 (14,28 με ΦΠΑ)
DFRobot, FIT0563
INTRODUCTION This immersible pump can be used to water your plants, make a fountain or waterfall, even change your fish tank water. It comes with an...
Άμεση
+
Προσθήκη στα αγαπημένα

074.0012
13,80 (17,11 με ΦΠΑ)
DFRobot, SEN0204, 5212019509138

This is a non-contact water / liquid level sensor for Arduino. It utilizes advanced signal processing technology by using a powerful chip (XKC-Y25-T12V) with high-speed operation capacity to achieve non-contact liquid level detection. No contact with liquid makes the module suitable for hazardous applications such as detecting toxic substances, strong acid, strong alkali and all kinds of liquid in an airtight container under high pressure. There are no special requirements for the liquid or container and the sensor is easy to use and easy to install.

Άμεση
+
Προσθήκη στα αγαπημένα

074.0002
14,00 (17,36 με ΦΠΑ)
DFRobot, SEN0216, 5212019509145

The Water Flow sensor measures the rate of a liquid flowing through it. The YF-S401 water flow sensor consists of a plastic valve body, flow rotor and hall effect sensor. It is usually used at the inlet end to detect the amount of flow. When liquid flows through the sensor, a magnetic rotor will rotate and the rate of rotation will vary with the rate of flow. The hall effect sensor will then output a pulse width signal. Connect it to a microcontroller and you can monitor multiple devices such as your coffee maker, sprinkler or anything else, and control the water flow rate to suit your needs!

Άμεση
+
Προσθήκη στα αγαπημένα

074.0255
14,51 (17,99 με ΦΠΑ)
DFRobot, FIT0212
INTRODUCTION This non-contact liquid level switch can be triggered when the liquid level fall below the sensor...
Άμεση
+
Προσθήκη στα αγαπημένα