MikroTik RB911G-5HPacD, 720Mhz, 128MB, 1xGigabit, onboard 1300mW 802.11ac Two Chain 5Ghz wireless, L3
Εγγύηση:
- 1 έτος
RB911G-5HPacD
RouterBOARD 911G-5HPacD is our low-cost small form factor CPE board with 802.11ac support. It's perfect for building low-cost 802.11ac CPE devices, as the list price is only $79. Yet, the device is very powerful- it's equipped with 720MHz CPU, 128MB RAM, Gigabit Ethernet port, power jack and 1300mW 802.11ac 5GHz Dual Chain wireless onboard. Comes with RouterOS L3 license.
Product specifications
| Details | |
| Product code | RB911G-5HPacD |
| CPU nominal frequency | 720 MHz |
| CPU core count | 1 |
| Size of RAM | 128 MB |
| 10/100/1000 Ethernet ports | 1 |
| Wireless standards | 802.11a/n/ac |
| Wireless chip model | QCA9882 |
| Power Jack | 1 |
| Supported input voltage | 8 V - 30 V |
| PoE in | Yes |
| Voltage Monitor | Yes |
| PCB temperature monitor | Yes |
| Dimensions | 105x105mm |
| Operating System | RouterOS |
| Operating temperature range | -40°C .. +70°C tested |
| License level | 3 |
| CPU | QCA9557 |
| Max Power consumption | 12W |
| Number of chains | 2 |
| Storage type | NAND |
| Storage size | 128 MB |
| Suggested price | $79.00 |
Wireless specifications
| 5 GHz | ||
| TX | RX | |
| 6MBit/s | 31 | -96 |
| 54MBit/s | 27 | -81 |
| MCS0 | 30 | -96 |
| MCS7 | 27 | -77 |
| MCS9 | 22 | -72 |
wireless parameters may be limited in software, depending on your local regulatory limitations
Performance test results
| RB911G-5HPacD | QCA9550 1G all port test | ||||||
| Mode | Configuration | 1518 byte | 512 byte | 64 byte | |||
| kpps | Mbps | kpps | Mbps | kpps | Mbps | ||
| Bridging | none (fast path) | 162.4 | 1,972.2 | 170.8 | 699.6 | 370.2 | 189.5 |
| Bridging | 25 bridge filter rules | 162.4 | 1,972.2 | 111.8 | 457.9 | 99.9 | 51.1 |
| Routing | none (fast path) | 162.4 | 1,972.2 | 317.4 | 1,300.1 | 370.2 | 189.5 |
| Routing | 25 simple queues | 162.4 | 1,972.2 | 174.2 | 713.5 | 176.2 | 90.2 |
| Routing | 25 ip filter rules | 60.2 | 731.1 | 62.8 | 257.2 | 61.8 | 31.6 |
1.All tests are done with Xena Networks specialized test equipment (XenaBay),and done according to RFC2544 (Xena2544)
2.Max throughput is determined with 30+ second attempts with 0,1% packet loss tolerance in 64, 512, 1518 byte packet sizes
3.Values in Italic indicate that max throughput was reached without maxing out CPU, but because board interface configuration was maxed out
4.Test results show device maximum performance, and are reached using mentioned hardware and software configuration, different configurations most likely will result in lower results
Σχετικά Αρχεία:
Πελάτες μας αγόρασαν επίσης
