iCOM IC-F1000T
IDAS™ Digital Mode Operation
The IC-F1000D/F2000D can program Type-D single-site trunking and digital conventional modes as well as analogue mode per channel. The IDAS digital mode employs 4-level FSK modulation and the NXDN™ common air interface, offering true 6.25kHz spectrum efficiency, higher security and better audio clarity – even at the fringes of the communication range. The following IDAS features are programmable:
- PTT ID (TX)
- Individual/group calls
- Radio check (RX)
- Stun/Kill/Revive (RX)
- Remote monitor (RX)
- Emergency (TX)
- Call alert (RX)
- Digital voice scrambler (15-bit)
- Status Call (Power ON/OFF status and GPS request)
- Voting scan for multi-site conventional operation
TX: Transmit, RX: Receive
Intelligent Emergency Functions
To assist in worker safety, the IC-F1000D/F2000D has three emergency related functions: motion detection, man down and lone worker functions. If one of these functions are activated, the transceiver automatically enters an emergency phase and starts counting down to send an emergency signal. The built-in motion sensor detects position, state of motion and non-motion.
Optional GPS Speaker-Microphone
With the optional GPS speaker-microphone, HM-171GPW, GPS position data can be attached to a voice or data transmission such as responding a GPS request status call.
IP67 Waterproof and Dust-tight Protection
While the body is compact, the IC-F1000D/F2000D has rugged construction providing superior protection against water (1m depth for 30 minutes), dust, sand, mud and other objects. The radio is also tested to MIL-STD 810 specifications. It can withstand harsh use.
Slim, Compact and Lightweight
The IC-F1000D/F2000D has a compact 52.2×111.8×30.3mm body and weighs only 260g (with BP-280 battery pack and belt clip). It's easy to carry around anywhere.
Easy to Hear in a Noisy Environment
The large 36mm speaker of the transceiver provides
clear 800mW* audio.
The built-in BTL amplifier increases the audio
output power and delivers loud and intelligible voice to a radio
operator working in noisy environments.
* Typical with internal speaker.
Built-in 2-Tone and 5-Tone (Analogue mode)
The IC-F1000D/F2000D has built-in 2-Tone, 5-Tone, CTCSS and DTCS signaling capability for analogue mode group communication and selective calling. The IC-F1000D/F2000D can be used as an analogue transceiver ready for future digital migration.
Long-Lasting Battery Pack
The large capacity waterproof battery pack, BP-280 (2400mAh typ.), provides 18 hours of operating time*.
The supplied rapid charger BC-213* charges the BP-280 in 3.5 hours.
* Tx: Rx: Standby=5:5:90. Power save function ON. BC-213 may be not supplied depending on version.
Other Features
- DTMF autodial memories
- MDC functions:
PTT ID, emergency call, radio check (RX) and stun/revive (RX) - BIIS PTT ID call
- Surveillance function
- Escalating alarm
- VOX capability for hands-free operation
- Channel announcement function
- Red emergency switch on the top panel
General
IC-F1000D |
IC-F2000D |
||
|---|---|---|---|
| Frequency coverage | 136–174MHz | 400–470MHz | |
| Number of channels | 16 channels | ||
| Type of emission (* Depending on version) |
16K0F3E (25kHz), 14K0F3E (20kHz), 8K50F3E (12.5kHz), 4K00F1E/D (6.25kHz) |
||
| Power supply requirement | 7.5V DC nominal | ||
| Current drain (approx.) | Tx High | 1.3A | 1.4A |
| Rx Max. audio /Standby |
400mA (Internal SP) /110mA |
400mA (Internal SP) /110mA |
|
| Antenna impedance | 50Ω | ||
| Operating temperature range | −25°C to +55°C (Radio specifications) | ||
| Dimensions (W×H×D) (Projections not included) |
52.2×111.8×30.3 mm (With BP-280) | ||
| Weight (approx.) | 260g (With MB-133 and BP-280) | ||
Transmitter
IC-F1000D |
IC-F2000D |
||
|---|---|---|---|
| Output power (at 7.5V DC) | 5W, 2W, 1W (Hi, L2, L1) | 4W, 2W, 1W (Hi, L2, L1) | |
| Max. frequency deviation | ±5.0kHz/±4.5kHz/±2.5kHz (Wide/Middle/Narrow) | ||
| Frequency stability | ±1.0ppm | ||
| Spurious emissions | 0.25μW (≤ 1GHz), 1.0μW (> 1GHz) | ||
| Residual modulation | 52/50/46dB typ. (W/M/N) | 54/53/48dB typ. (W/M/N) | |
| Audio harmonic distortion (AF 1kHz 40% deviation) |
2.0%/1.1%/1.1% typ. (Wide/Middle/Narrow) | 1.0%/1.0%/1.5% typ. (Wide/Middle/Narrow) | |
| FSK error | 5.0% max. | ||
| Ext. microphone connector | 3-conductor 2.5 (d) mm (1/10″)/2.2kΩ | ||
Receiver
IC-F1000D |
IC-F2000D |
||
|---|---|---|---|
| Sensitivity | at 20dB SINAD | –4dBμV emf typ. (W/M/N) |
–5/–5/–2dB emf typ. (W/M/N) |
| at 5% BER | –8dBμV emf typ. (Digital) |
–8dBμV emf typ. (Digital) |
|
| Adjacent channel selectivity | y 77/74/69dB typ. (W/M/N) 59dB typ. (Digital) |
75/74/69dB typ. (W/M/N) 58dB typ. (Digital) |
|
| Spurious response rejection | 80dB typ. | ||
| Intermodulation rejection | 69dB typ. (W/M/N) 74dBμV emf typ. (Digital) | 70dB typ. (W/M/N) 74dBμV emf typ. (Digital) | |
| Hum and noise | 52/50/46dB typ. (W/M/N) | 50/48/45dB typ. (W/M/N) | |
| Audio output power | Internal SP (With 12Ω load) |
800mW typ. (at 5% distortion) | |
| External SP (With 8Ω load) |
400mW typ. (at 5% distortion) | ||
| Ext. speaker connector | 2-conductor 3.5 (d) mm (1/8″)/8Ω | ||
Applicable U.S. Military Specifications
Icom makes rugged products that have been tested to and passed the following MIL-STD requirements and strict environmental standards.
| Standard | MIL-810 G Method, Procedure |
|---|---|
| Low Pressure Storage | 500.5 I |
| Low Pressure Operation | 500.5 II |
| High Temperature Storage | 501.5 I |
| High Temperature Operation | 501.5 II |
| Low Temperature Storage | 502.5 I |
| Low Temperature Operation | 502.5 II |
| Temperature Shock | 503.5 I |
| Solar Radiation | 505.5 I |
| Rain Blowing | 506.5 I |
| Rain Drip | 506.5 III |
| Humidity Induced | 507.5 |
| Salt Fog | 509.5 |
| Dust Blowing | 510.5 I |
| Immersion | 512.5 I |
| Vibration | 514.6 I |
| Shock Functional | 516.6 I |
| Shock Transit Drop | 516.6 IV |
| Ingress Protection Standard | |
|---|---|
| Dust & Water | IP67 (Dust-tight and waterproof protection) |
All stated specifications are subject to change without notice or obligation.
