iCOM IC-F1000S
Please sign in so that we can notify you about a reply
Specifications
| General | |||
|---|---|---|---|
|
Frequency coverage (MHz) |
F1000/S/T
136–174MHz F2000/S/T
400-470MHz 450-512MHz |
||
| Number of channels |
F1000
16 channels F1000S/T 128 F2000
16 channels F2000S/T 128 |
||
| Type of emissions | 16K0F3E*/11K0F3E | ||
| Channel spacing | 12.5/25kHz (Not USA Version) | ||
| Power supply requirement | 7.5V DC nominal | ||
| Current drain TX High RX Max. auidio/ Sandby |
|
||
| Antenna impedance | 50Ω | ||
| Operating temperature range | -30°C to 60°C; –22°F to +140°F (radio only) | ||
| Dimensions (W×H×D) (Projections not included) |
52.2×111.5×24.5mm; 2.06×4.39×0.96 in (With BP-279) | ||
| Weight | 240g; 8.47oz (With BP-279) | ||
| Transmitter | |||
| Output power |
F1000/S/T
5W, 2W, 1W (Hi, L2, L1) F2000/S/T
4W, 2W, 1W (Hi, L2, L1) |
||
| Max. frequency deviation | ± 5.0kHz/±2.5kHz (Wide/Narrow) | ||
| Frequency stability | ±2.5ppm | ||
| Spurious emissions | 70dB min. | ||
| FM hum and noise | 46/40dB typ. (Wide/Narrow) | ||
| Audio harmonic distortion | 1.0%/1.5% typ. (W/N, AF 1kHz 40% deviation) | ||
| Ext. microphone connector | 2-conductor 3.5 (d) mm (1⁄10")⁄2.2kΩ | ||
| Receiver | |||
| Sensitivity (at 12dB SINAD) | 0.25μV typ. | ||
| Adjacent channel selectivity |
F1000/S/T
76/53dB typ. (W/N) F2000/S/T
73/56dB typ. (W/N) |
||
| Spurious response | 70dB min. | ||
| Intermodulation |
F1000/S/T
74dB typ. F2000/S/T
73dB typ. |
||
| Hum and noise |
F1000/S/T
51/45dB typ. (W/N) F2000/S/T
49/43dB typ. (W/N) |
||
| Ext. speaker connector | 2-conductor 3.5 (d) mm (1⁄8")/8Ω | ||
| Audio output power (at 5% distortion) Internal SP (w/12Ω load) External SP (w/8Ω load) |
800mW typ. (at 5% distortion) 400mW typ. (at 5% distortion) |
||
Measurements made in accordance with TIA-603.
All stated specifications are subject to change without notice or obligation.
* 25kHz bandwidth is no longer available for FCC Part 90 licensees for USA versions.
Ask your dealer if you need 25kHz bandwidth.
Applicable U.S. Military Specifications
Icom makes rugged products that meet MIL-STD requirements and strict environmental standards as follows.
| Standard | MIL 810 G | |
| Method | Proc | |
| Low Pressure | 500.5 | I, II |
| High Temp. | 501.5 | I, II |
| Low Temp. | 502.5 | I, II |
| Temp. Shock | 503.5 | I-C |
| Solar Radiation | 505.5 | I |
| Rain Blowing/Drip | 506.5 | I, III |
| Humidity | 507.5 | II |
| Salt Fog | 509.5 | – |
| Dust Blowing | 510.5 | I |
| Immersion | 512.5 | I |
| Vibration | 514.6 | I |
| Shock | 516.6 | I, IV |
Also meets equivalent MIL-STD-810-C, -D, -E and -F.
| Ingress Protection Standard | |
| Dust & Water | IP67 (Dust-tight and waterproof protection) |
Supplied accessories
- Battery pack, BP-279
- Belt clip, MB-133
- Antenna FA-SC57U or FA-SC55V
